FileZilla Server2: Basic Configuration 1

Uniform Server 4.1-Mona
FileZilla FTPd (Server).

FileZilla Server basic set-up

This page is a basic introduction to running portable FileZilla and assumes you have installed FileZilla for basic (portable) operation. Advantages of portable operation you can explore and test configurations if you break anything just throw it away and start again.

Start servers

Both UniServer and FileZilla servers need to be running before using FileZilla admin. You can start the servers in any order however portable operation imposes some restrictions. Starting FileZilla first results in a nag screen, the correct order is:

Navigate to folder UniServer
Start UniForm Server – Double click on Server_Start.bat - Note the virtual drive created (Normally Z).
Start FileZilla server – Double click on fz_start.bat

Note: Only portable mode requires this restriction. More specifically it’s the creation of a virtual drive that is required. Neither Apache nor MySQL need to be running.

Top

Start FileZilla Admin

Navigate to folder UniServer
Double click on file fz_admin.bat
A pop-up (Connect to server) is displayed, click OK - Starts admin window.
Logged on confirms connection to server
If the connection fails an error message is displayed. Several attempts are made before eventually giving up.

Admin:

The admin interface provides access to three server

sections, setting, users and groups. Two selection

methods are available either via the top row of icons

or using the drop down menu.

Settings: Top row icon A) dropdown menu A1)
Users: Top row icon B) dropdown menu B1)
Groups: Top row icon C) dropdown menu C1)

Top

User accounts

Create a user:

For this example we will create a user fred with password fred123

From Zilla Admin select Edit > Users B1)
Users window displayed
Select page General - selected by default D)
Under users click Add E)
Add user account pop-up displayed
Type a new user name e.g. fred F)
Click OK - Add user account pop-up disappears G)
Check Enable account - Checked by default H)
Check Password box J)
Enter a password e.g. fred123 K)

If you click OK bottom left the following error message is displayed:

You need to share at least one directory and set it as home directory

Note 1: Directory and folder are the same thing in the next section we asssign a folder to this user.

Note 2: You can return to this page at any time, add or delete users, change passwords or even allow name access only.

Assign a user folder:

For this example we will assign the root folder www to fred.

Select page Shared folders - Selected by default L)
Select user - Selected by default single user M)
Under shared folders click Add N)
In the pop-up navigate to folder z:\www click to highlight click OK.
Note: Your virtual drive letter may differ
The folder selected is displayed O)
to the left of this make sure “H” is displayed
if not clcik “Set as home dir” P)
Select file privileges you wish to allow Q)
Select directory privileges you wish to allow R)
Click OK S)

Notes:

For each new user repeat steps 3-16. You can change user privileges and delete users as required.

Restart the server to guarantee changes take effect (generally not required)

For step 12 image shows folder F:\z_temp simply because I am reusing the image it should display z:\www however the drive letter may be different in your case, depends on virtual drive created.

Top

Quick Test

Assuming you are running the server on your local machine you can quickly test the account.

Type the following into your browser:

ftp://localhost/ a pop-up is displayed enter name (fred) and password (fred123).

A page is displayed showing files and folders contained in your shared folder (www).

Local network access

Anyone on your local network can access the ftp server by typing ftp://your_ip_address into their browser; they will be challenged for a user name and password.

To find your IP address use a command prompt:

Open command prompt start > run > type in cmd > clik OK
In the command window type ipconfig /all
Look for your IP address. If you are using a wireless network the address will be similar to this 192.168.1.6
While in the command window look for Host Name (my PC name is mpg2) the name of your PC
(note sometimes this is not set-up)

A user can use either HostName or IP address to access your FTP server for example:

A user on your network would then type ftp://192.168.1.6/ Or ftp://mpg2/

Neither of the above is very easy on the eye an alternative is to get each user to add a memorable name to their hosts file. For example under localhost add a line as shown below:

127.0.0.1 localhost
192.168.1.6 my_ftp_server

They must substitute 192.168.1.6 for your IP address and replace my_ftp_server with a memorable name, which they would like to use.

Internet access

To access your FTP server from the Internet a user would type the following into a browser:

ftp://your_domain_name/ alternatively ftp://your_external_ip_address

On-line help:

Testing an FTP server for online access can be problematic however there are two useful online services that can help:

To find your external IP address use: Whatsmyip

To test FTP access use: Gene6 FTP Server Test, its free for anyone to use.

Ports:

If you have a direct Internet connection there should be no problems with access.
However if you are using a router you need to forward ports 20 and 21 every router is different hence pay a visit to PortForwrd for detailed instructions.

Top

Problems

You may be unlucky and have a service provider that blocks the common FTP ports. In this event try changing the ports. Do not allow your firewall to block Internet access otherwise you will need to manually enable access.

Top

FTP Clients

Using a browser allows for quick testing however an FTP client offers more flexibility my personal favourite is FireFTP running on Firefox. It’s a personal taste hence choose one that suits your needs.

Top

Summary

The above shows how easy FileZilla server is to set-up and test. The next page covers mapping alias folders.

Top